Претрага
2348 items
-
Natural two-dimensional pyrophyllite: Nanoscale lubricant, electrical insulator and easily-machinable material
Borislav Vasić, Radoš Gajić, Ivana Milošević, Žarko Medić, Marina Blagojev, Marko Opačić, Aleksandar Kremenović, Dejan Lazić (2022)Pyrophyllite, with the chemical formula Al2Si4O10(OH)2, is a naturally occurring and abundant van der Waals mineral belonging to the group of phyllosilicates. It is very soft, layered crystal used for sculpting and an excellent electrical and thermal insulator aimed for the operation at high pressure and temperature. Here, for the first time, two-dimensional (2D) pyrophyllite obtained by both mechanical and liquid phase exfoliation is presented and investigated at the nanoscale. The layered structure provides low friction coefficient of around ...Atomic force microscopy, Insulating properties, Nanofriction and wear, Natural two dimensional materials, Phyllosilicates, PyrophylliteBorislav Vasić, Radoš Gajić, Ivana Milošević, Žarko Medić, Marina Blagojev, Marko Opačić, Aleksandar Kremenović, Dejan Lazić. "Natural two-dimensional pyrophyllite: Nanoscale lubricant, electrical insulator and easily-machinable material" in Applied Surface Science, Elsevier BV (2022). https://doi.org/10.1016/j.apsusc.2022.155114
-
Adaptive neuro-fuzzy prediction of operation of the bucket wheel drive based on wear of cutting elements
The capacity of the rotor excavator depends largely on the operation of the subsystem for digging. There is a great contribution to the correct and sharp teeth when the capacity is the highest. In the function of time, the teeth become clogged due to abrasive wear, or changes in their geometric shape. To analyze the bucket wheel drive in depend on wear of the cutting elements in this study adaptive neuro fuzzy inference system (ANFIS) approach was implemented. ANFIS ...Filip Miletić, Predrag D. Jovančić, Milos Milovančević, Dragan Ignjatović. "Adaptive neuro-fuzzy prediction of operation of the bucket wheel drive based on wear of cutting elements" in Advances in Engineering Software, Elsevier BV (2020). https://doi.org/10.1016/j.advengsoft.2020.102824
-
Утицај похабаности резних елемената роторног багера на ниво вибрација погона за копање
Филип Милетић (2023)У докторској дисертацији је анализиран утицај похабаности резних елемената роторног багера на потрошњу електричне енергије и ниво амплитуде вибрација погона за копање. Креиран је модел који у функцији стања резних елемената дефинише зависност разматраних физичких феномена. За развој модела примењене су једначине теорије осцилација и Ватметарска метода [1] којом се одређује потрошња електричне енергије. За верификацију модела извршена су мерења на роторном багеру SRs2000.32/5+VR ангажованом на откопавању откривке на површинском копу Тамнава–Западно поље. Обављено је пет мерења. Резни елементи су ...Филип Милетић. Утицај похабаности резних елемената роторног багера на ниво вибрација погона за копање, Београд : [Ф. Милетић], 2023
-
Basalt-polyester hybrid composite materials for demanding wear applications
Faisal Abusahmin, Ahmed Algellai, Nataša Tomić, Marija Vuksanović, Jelena Majstorović, Tatjana Volkov-Husović, Vladimir Simić, Radmila Jančić-Heinemann, Marinko Toljić, Jovan Kovačević (2020)Faisal Abusahmin, Ahmed Algellai, Nataša Tomić, Marija Vuksanović, Jelena Majstorović, Tatjana Volkov-Husović, Vladimir Simić, Radmila Jančić-Heinemann, Marinko Toljić, Jovan Kovačević. "Basalt-polyester hybrid composite materials for demanding wear applications" in Science of Sintering, National Library of Serbia (2020). https://doi.org/10.2298/SOS2001067A
-
Extensive vibrations of the belt conveyer drive electromotor of a bucket wheel excavator as a result of intesified wear-and-tear of its mount support
Vesna Damnjanović, Predrag Jovančić, Snežana Aleksandrović. "Extensive vibrations of the belt conveyer drive electromotor of a bucket wheel excavator as a result of intesified wear-and-tear of its mount support" in Journal of Vibroengineering (2017). https://doi.org/10.21595/jve.2016.17321
-
Determining the Impact of Cutting Elements State on the Bucket–Wheel Excavator Vibration and Energy Consumption
Background There are two types of specifc sizes’ measurements. The frst is the measurement of energy consumption in a working technological process, and the second is the measurement of vibration, which is displayed over amplitudes of speed. There is an interplay between these two processes. Increasing the power consumption, the value of the vibration speed amplitudes increases. Purpose The process of the determination of machining parameters was based on minimizing the power consumption and vibration of the cutting tool, ...Filip Miletić, Predrag Jovančić, Miloš Milovančević, Miloš Tanasijević, Stevan Đenadić. "Determining the Impact of Cutting Elements State on the Bucket–Wheel Excavator Vibration and Energy Consumption" in Journal of Vibration Engineering & Technologies, Springer (2022). https://doi.org/10.1007/s42417-022-00482-3
-
Pleistocene rhinoceros from Bogovina Cave: the first report of Stephanorhinus hundsheimensis Toula, 1902 (Mammalia, Rhinocerotidae) from Serbia
Finds of Pleistocene rhinoceros are rare in Serbia, and only one species (the woolly rhinoceros Coelodonta antiquitatis Blumenbach, 1799) has been reported so far. The current paper presents the dental material of an extinct so-called Hundsheim rhinoceros, Stephanorhinus hundsheimensis Toula, 1902 from Bogovina Cave (East ern Serbia). Both the morphological and metric characteristics of the teeth are consis tent with the attribution to S. hundsheimensis. Unfortunately, the rhinoceros material originated from an uncertain geological context, so there is no ...... relatively small mesial valley and a larger distal one, both with V-shaped outlines in the lingual view, and a right-angled vestibular syncline. Mesial and distal cingula (oblique and continuous) are evidently present, though obscured by inter- proximal wear; a faint, horizontal and discontinu- ous cingulum ...
... Latest Villafranchian and Galerian, late Early and early Middle Pleistocene of Europe (1.4–1.2 Ma until 0.6–0.5 Ma), and possibly Late Pleistocene of Western Asia (Caucasus). Description. Upper dentition: The specimen NMKVRS.P13 (Fig- ure 3A-E) is a left P3 or P4. Despite pronounced wear, this middle-large ...
... brown crown with very pronounced rounding and polishing presumably by water transport. Large parts of the mesial, distal, and vestibular enamel are missing. The preserved occlusal sur- face shows marked wear, the presence of an inte- rior valley, a single crochet, and the postfossetta. A partially preserved ...Predrag Radović, Miloš Radonjić, Emmanuel Billia. "Pleistocene rhinoceros from Bogovina Cave: the first report of Stephanorhinus hundsheimensis Toula, 1902 (Mammalia, Rhinocerotidae) from Serbia" in Palaeontologia Electronica, Coquina Press (2020). https://doi.org/10.26879/985
-
Behavior Determining of Bucket Wheel Drive Depending on the Wear Impact of the Cutting Elements
Miletić Filip, Jovančić Predrag, Đenadić Stevan. "Behavior Determining of Bucket Wheel Drive Depending on the Wear Impact of the Cutting Elements" in Procedia Structural Integrity 13, :Elsevier (2018): 1644-1650. https://doi.org/https://doi.org/10.1016/j.pros
-
Linear-motor plunger pump increases lifting efficiency
Bojan Martinović, Dušan Đekić, Dušan Danilović, Pavel Isaev. "Linear-motor plunger pump increases lifting efficiency" in Oil & Gas Journal (2022)
-
Characterization and Environmental Evaluation of Recycled Aggregates from Construction and Demolition Waste in Belgrade City Area (Serbia)
Filip Abramović, Miroslav Popović, Vladimir Simić, Vesna Matović, Radmila Šerović. "Characterization and Environmental Evaluation of Recycled Aggregates from Construction and Demolition Waste in Belgrade City Area (Serbia)" in Materials, MDPI AG (2024). https://doi.org/10.3390/ma17040820
-
Automated blasthole drilling in surface mining
Milanka Negovanović, Lazar Kričak (2021)Све већи развој аутоматизације у рударској индустрији утицао је на увођење нових решења у области аутоматизације бушења минских бушотина на површинским коповима. Највећи светски произвођачи опреме за бушење развијају решења аутоматизације која омогућавају рударским компанијама да постигну најбоље резултате у погледу квалитета, продуктивности и оперативних трошкова. Решења из области аутоматизације бушења се крећу од операција даљинског управљања до потпуно аутоматизованог бушења, праћења података у реалном времену и разних специјализованих алата за управљање подацима који повећавају безбедност и продуктивност ...Аутоматизација, бушилица,тачност, бушење,рударство,систем даљинског управљања,безбедност, продуктивностMilanka Negovanović, Lazar Kričak . "Automated blasthole drilling in surface mining" in 8th International Conference Mining And Environmental Protection, Sokobanja, 22 – 25th September 2021 Serbia, University of Belgrade, Faculty of Mining and Geology, Belgrade, Serbia (2021)
-
Mesozoic carbonate rocks in Serbia used as dimension stone
Vesna Matović, Tijana Vojnović Ćalić (2016)The building industry in Serbia uses, to a great extent, imported natural stone for architectural purposes. The significance of local deposits, particularly limestones, is not adequately perceived despite the country’s abundance of these valuable resources. Therefore, this study focuses on Serbia’s Mesozoic carbonate rocks, specifically on the deposits of four selected quarries: Klisura, Skrzut, Struganik, and Tisnica. The quality and prospects of the application of these limestones has not yet been the subject of a detailed, comprehensive investigation. Therefore, ...... ed limestones are predominantly hard rocks (Bilbija and Matović 2009). They have equable saturated and after freeze-thaw cycling (G); and d wear abrasive (Hb); legend: K/ klisura, 7S tisnica, S7 struganik, SK skrzut means of abrasion wear (volume loss) that vary from 16.5 to 19.4 cm?/50 cm* ...
... values (<120 N/mm?) of Skrzut limestone and the abrasion wear values (>18 cm?/50 cm?) of Klisura and Struganik limestones, these rocks are applicable for paving exterior horizontal surfaces of mod- erate pedestrian traffic areas. Owing to both the strength and abrasion values, Tisnica limestone is ...
... selected quarries was determined. It is shown (Table 2) that due to the abrasion wear values (>25 cm*/50 cm?) the application of all observed limestones as horizontal interior surfaces is limited to intensive and moderate pedestrian traffic areas (SRPS B.B3.200 1994). The national standard proposes ...Vesna Matović, Tijana Vojnović Ćalić. "Mesozoic carbonate rocks in Serbia used as dimension stone" in Bulletin of Engineering Geology and the Environment, Springer Science and Business Media LLC (2016). https://doi.org/10.1007/s10064-015-0722-0
-
Overwiew of In-Pit Crushing & Conveying Technology in Open Pit Mines
The conditions under which contemporary surface mining operations is carried out obviously becoming increasingly complex. In such complex conditions, the optimization of haulage systems as the technological phase with the largest share in the total operating costs, is very important from the aspect of achieving profitability of the mining project. In a large number of cases, the application of traditional haulage systems with trucks (as the most dominant type of haulage in open pit mines) does not lead to ...Ali Nasirinezhad, Dejan Stevanović, Dragan Ignjatović, Petar Marković. "Overwiew of In-Pit Crushing & Conveying Technology in Open Pit Mines" in 8th International Conference MIining And Environmental Protection, Sokobanja, 22-25 September 2021, University of Belgrade, Faculty of Mining and Geology, Belgrade, Serbia (2021)
-
A Model for Determining Fuzzy Evaluations of Partial Indicators of Availability for High-Capacity Continuous Systems at Coal Open Pits Using a Neuro-Fuzzy Inference System
This paper presents a model for determining fuzzy evaluations of partial indicators of the availability of continuous systems at coal open pits using a neuro-fuzzy inference system. The system itself is a combination of fuzzy logic and artificial neural networks. The system availability is divided into partial indicators. By combining the fuzzy logic and artificial neural networks, a model is obtained that has the ability to learn and uses expert judgment for that learning. This paper deals with the ...системи, континуални системи експлоатације (роторни багер-транспортер-дробилично постројење), рударство, расположивост, меко рачунарство, фази логика, ANN, ANFISMiljan Gomilanović, Miloš Tanasijević, Saša Stepanović, Filip Miletić. "A Model for Determining Fuzzy Evaluations of Partial Indicators of Availability for High-Capacity Continuous Systems at Coal Open Pits Using a Neuro-Fuzzy Inference System" in Energies, MDPI AG (2023). https://doi.org/10.3390/en16072958
-
English for Geology Students. 1
Lidija Beko (2023)... roughly 40 and 60 degrees centigrade, and this, coupled with the high humidity and acidity of the atmosphere, mean it is necessary for anyone visiting the Cave to wear a protective “ice suit”. The Caves have been flooded for much oftheir history, and the unique conditions of the heat and the solute ...
... collected from Mars. Such explorations and studies allow scientists to construct a picture of the similarities and differenc- es between the Earth and other extraterrestrial bod- ies, much as doctors might build up a picture of genetic similarities and differences in a family. While many ...
... s carried into orbit by satellites. This has resulted in an increased ability to test and prove hypotheses, and also 12 Meteorite created new ways of studying the interactions of terrestrial cycles and systems on a truly global scale, leading to a new field of research known as Earth system ...Lidija Beko. English for Geology Students. 1, Belgrade : The Faculty of Mining and Geology, 2023
-
Cutting Resistance Laboratory Testing Methodology for Underwater Coal Mining
... Validation, V.R., S.Ð., and F.M.; Formal analysis, V.R.; Investigation, V.Č. and V.R.; Resources, V.Č. and V.R.; Data curation, V.R., S.Ð., and F.M.; Writing—original draft preparation, V.Č.; Writing—review and editing, V.R.; Visualization, S.Ð. and F.M. All authors have read and agreed to the published ...
... 1937, Kienast [11] studied the cutting process of bucket chain excavators to determine the optimum slice cross-section for the minimum bucket knife wear. Consequently, he mathematically calculated the minimum slice circumference by considering the rounding of bucket corners. Afterward, in 1955, Rasper ...
... 1937, Kienast [11] studied the cutting process of bucket chain excavators to determine the optimum slice cross-section for the minimum bucket knife wear. Consequently, he mathematically calculated the minimum slice circumference by considering the rounding of bucket corners. Afterward, in 1955, Rasper ...Vladimir Čebašek, Veljko Rupar, Stevan Đenadić, Filip Miletić. "Cutting Resistance Laboratory Testing Methodology for Underwater Coal Mining" in Minerals, MDPI AG (2021). https://doi.org/10.3390/min11060564
-
Flyrock induced by blasting in surface mining
Milanka Negovanović, Lazar Kričak, Snežana Ignjatović, Stefan Milanović, Jovan Marković, Nikola Simić, Rade Šarac (2022)Miniranje predstavlja i dalje najefikasniji i najjeftiniji način eksploatacije velikih količina čvrstih mineralnih sirovina na površinskim kopovima. Energija eksplozije se koristi za fragmentaciju čvrste stenske mase do zahtevane granulacije. Pored pozitivnih efekata miniranja, postoje i određeni neželjeni efekti svakog procesa miniranja koji se mogu javiti, a to su: potresi tla, razletanje komada stene, vazdušni udari, otrovni i zagušljivi gasovi i prašina. Razletanje komada stene je nekontrolisano izbacivanje fragmenata odminirane stenske mase i predstavlja jedan od glavnih izvora materijalne štete ...Milanka Negovanović, Lazar Kričak, Snežana Ignjatović, Stefan Milanović, Jovan Marković, Nikola Simić, Rade Šarac. "Flyrock induced by blasting in surface mining" in Rudarski glasnik, Beograd : Rudarski institut (2022). https://doi.org/10.25075/BM.2022.05
-
Application of Expansive Mortars for the Formation of Artificial Screens During Blasting in Urban Areas
During construction of buildings in urban areas, sometimes there is a need to blast solid rock mass in the immediate vicinity of the surrounding buildings. In that case, the aim is not only to increase the efficiency of blasting, but also to reduce harmful effects of ground vibration induced by blasting. At the same time, it is very important to protect the buildings located in the safe zone from the blast site as well as remaining rock mass around ...Milanka Negovanović, Lazar Kričak, Stefan Milanović, Nikola Simić, Jelena Majstorović. "Application of Expansive Mortars for the Formation of Artificial Screens During Blasting in Urban Areas" in 31st International Conference Ecological Truth & Environmental Research-EcoTER'24, Sokobanja, 18-21. jun 2024, Bor : Tehnički fakultet u Boru (2024)
-
Improving efficiency of thermal power plants through mine coal quality planning and control
Главни циљ контроле квалитета угља у рудницима лигнита је снабдевање термоелектрана угљем чији квалитет мора да се креће унутар одређених квалитативних ограничења. Карактеристике угља могу да утичу на ефикасност, поузданост и расположивост како котла тако и јединица за контролу емисије. У овом раду аутори су презентовали интегрисану симулацију рударског процеса као нови приступ у истраживању променљивости калоричне вредности угља приликом експлоатације комплексног лежишта лигнита. Резултати таквог приступа омогућавају драгоцен увид у перформансе континуалног рударског система у смислу контроле променљивости ...Mirjana Banković, Dejan Stevanović, Milica Pešić, Aleksandra Tomašević, Ljiljana Kolonja. "Improving efficiency of thermal power plants through mine coal quality planning and control" in Thermal Science, Vinča Institute of Nuclear Sciences (2018). https://doi.org/10.2298/TSCI170605209B
-
Definition of criteria and alternatives for choosing the optimal mining method deposits when applying multi: Criteria optimization, Belgrade, June 2024
Sanja Bajić, Dragoljub Bajić, Branko Gluščević, Radmila Gaćina, Josip Išek. "Definition of criteria and alternatives for choosing the optimal mining method deposits when applying multi: Criteria optimization, Belgrade, June 2024" in Podzemni radovi, Beograd, jun 2024, Centre for Evaluation in Education and Science (CEON/CEES) (2024). https://doi.org/10.5937/podrad2444071B